top of page

Technical guides and insights
The TKS RaceLab technical blog on kart maintenance, engines and setup


How to install a Rotax engine on a kart chassis: step-by-step guide and torques
To install a Rotax engine on a kart chassis you bolt the engine plate under the engine, fix the clamps to the chassis tubes with abrasive paper underneath, fit the chain with about 5 mm of play and align the sprockets with a straight edge.

Sergio, TKS RaceLab
Oct 229 min read


Rotax engine exploded view: how to find the right spare part number
The Rotax engine exploded view is the illustrated parts catalogue: for each engine group there is a drawing with numbered parts and, below it, a table with position, part number, description and quantity for each category.

Sergio, TKS RaceLab
Oct 227 min read


Kart track logbook: what to write down every session (free PDF)
The track logbook is the technical diary of your kart: for every day you write down track conditions, starting set-up, what you changed in every session with lap time and feel, and the engine hours.

Sergio, TKS RaceLab
Oct 225 min read


Rotax reed valve: check, reeds and Micro and Mini kit
The Rotax reed valve is the valve that lets the mixture into the crankcase and stops it from flowing back towards the carburettor.

Sergio, TKS RaceLab
Oct 225 min read


Rotax crankshaft: when to rebuild it and which measurements to check
The Rotax crankshaft is checked at every engine rebuild, which on the 125 MAX evo and the DD2 is due every 50 running hours.

Sergio, TKS RaceLab
Oct 226 min read


Rotax MAX Torque Settings: The Complete Table for the 125 MAX evo Engine
Rotax MAX torque settings: all the values of the Rotax 125 MAX evo 2024 repair manual for cylinder, head, exhaust valve, intake, crankcase, clutch and starter.

Sergio, TKS RaceLab
Oct 205 min read


Kart cleaning: how to wash your kart after the track and what to check
Kart cleaning step by step: cold engine, intake sealed, air filter, radiator, brakes, lubrication after washing and the checks to do while you clean.

Sergio, TKS RaceLab
Oct 185 min read


Kart steering wheel and column: rules, setup and checks
Kart steering wheel and column: CIK-FIA rules on wheel, hub and column, how to bring the wheel closer or change its angle, and steering checks before a run.

Sergio, TKS RaceLab
Oct 184 min read


Kart pedals and throttle cable: setup, rules and checks
Kart pedals and throttle cable: CIK-FIA rules, pedal extension kits, how to set the throttle cable on the Rotax carburettor and checks before every run.

Sergio, TKS RaceLab
Oct 184 min read


Bent kart chassis: how to spot it and what to check
Bent kart chassis: the signs on track, the parts that bend first, how to check the chassis C brackets and when to straighten or replace it.

Sergio, TKS RaceLab
Oct 185 min read


Rotax fuel filter and pump: how they work and what to check
Rotax fuel filter and pump: how they work, where the filters are, when to clean or replace them and the signs of a fuel supply that isn't working well.

Sergio, TKS RaceLab
Oct 184 min read


Rotax ignition on the MAX EVO: how it works and what to check
Rotax MAX EVO ignition: ECU, pick-up, coil and battery, why the engine won't start and the checks to do in order before replacing parts.

Sergio, TKS RaceLab
Oct 185 min read


Kart transport: how to load it, secure it and get it to the track undamaged
Kart transport: van or trailer, how to load and secure the kart, carrying fuel safely and the checklist so you don't leave anything at home.

Sergio, TKS RaceLab
Oct 184 min read


Kart axle bearings: checks, signs of wear and replacement
Kart axle bearings: the 2-minute check, signs of wear, how to choose the right size and how to replace them without forcing the axle.

Sergio, TKS RaceLab
Oct 184 min read


Rotax exhaust: how it works and how to look after pipe, springs and silencer
Rotax exhaust: how the resonance pipe works, checks on springs, gasket and silencer, and the signs that tell you it's time to act.

Sergio, TKS RaceLab
Oct 184 min read


Kart bodywork after contact: what to check and what to replace
Kart bodywork after contact: checks on front fairing, mounting kit and side pods, the rules to know and when to replace parts.

Sergio, TKS RaceLab
Oct 184 min read


Rotax water pump: how it works, what to check and when to act
Rotax water pump: how it works, why there is no belt, the leakage bore on the crankcase, the right temperatures and genuine spare parts.

Sergio, TKS RaceLab
Oct 184 min read


Bought a used kart? The checks to do before taking it on track
Bought a used kart? The checks on chassis, steering, brakes, transmission, tyres and Rotax engine to do before the track, with a practical checklist.

Sergio, TKS RaceLab
Oct 188 min read


Kart winter storage: the checklist to lay it up without damage
Kart winter storage: the system-by-system checklist to protect engine, chassis, chain, tyres and battery and restart in spring without surprises.

Sergio, TKS RaceLab
Oct 184 min read


Rotax intake silencer: how to clean and oil the air filter
Rotax intake silencer: what it does, when and how to clean and oil the air filter, mistakes to avoid and spare parts.

Sergio, TKS RaceLab
Oct 184 min read
bottom of page
