top of page

TKS RaceLab - Your Karting Partner

Contact
Logo TKS RaceLab
Motore Rotax DD2

Kart axle bearings: checks, signs of wear and replacement

Writer: Sergio, TKS RaceLab
Sergio, TKS RaceLab
Oct 18
4 min read

Updated: 5 days ago


TKS RaceLab cover: kart axle bearings, checks, wear and replacement

Axle bearings work silently under huge loads, among vibration, dust and water. When they're in good condition you don't notice them. When they start to go, the kart loses free-running speed, the axle can move and in extreme cases it can break on track. Here is how to check kart axle bearings and when to replace them.

In short 2-minute check: lift the rear, remove the chain, spin the axle by hand. It should spin freely and smoothly, without tight spots, noise or play. Grub screws lock the bearing onto the axle and should be checked often. Size: the first number is the axle (50 mm), the second the outer diameter that must match the carrier. Avoid pressure washers on the bearings.

How kart axle bearings work

The rear axle turns on three bearings, mounted in carriers fixed to the chassis. Each bearing has two grub screws that lock the inner ring onto the axle: this way the axle doesn't slide sideways and turns with the inner ring, while the outer ring stays still in the carrier. If a bearing tightens up, it brakes the axle and costs you speed on the straight. If the grub screws loosen, the axle can shift sideways.

Maranello 50x90 axle bearing with grub screws, part AFN.00157

The 2-minute bearing check

• 1. Lift the rear: put the kart on the stand with the rear wheels off the ground.

• 2. Remove the chain: so you only feel the friction of the bearings, not of chain and engine.

• 3. Spin the axle by hand: it should spin freely for several turns and slow down gently. If it stops straight away or you feel tight spots, a bearing isn't right.

• 4. Look for play: try moving the axle up, down and sideways near each carrier. There should be no play.

• 5. Check the grub screws: they must be tight on all three bearings.

Use the check to inspect the chain as well: you'll find everything in the guide to chain tension and lubrication.


Signs of wear not to ignore

• Noise or roughness: a bearing that grinds or makes a metallic sound is worn.

• The axle doesn't spin freely: you lose speed on the straight without understanding why.

• Play: the axle moves in the carrier, the kart becomes less precise and strange behaviour can appear in corners. If the kart hops, also read kart hopping in corners.

• Rust or dark marks: water and dirt have got into the bearing.


How to choose the right size

On chassis with a 50 mm axle the most common bearings are the Maranello 50x90 axle bearing with grub screws (AFN.00157) and the Maranello 50x80 axle bearing with grub screws (AFN.01356). The first number is the inner diameter, that is the axle. The second is the outer diameter, which must match the carrier fitted on your chassis. For classes with a smaller axle there's the 40 mm axle bearing with grub screws. If you're unsure about the size, contact us before ordering.

Axle Bearing 40 with Grub Screws
Maranello 50x80 axle bearing with grub screws, part AFN.01356

How to replace kart axle bearings

To change the bearings you need to slide the axle out: the complete step-by-step procedure is in the guide how to change a kart axle. The key points:

• Loosen the grub screws first: an axle with tight grub screws won't slide out and gets damaged.

• Never hammer it: if the axle doesn't slide, clean it well and check for burrs and scratches.

• Align the bearings: fit the new bearings, insert the axle and leave the carriers slightly loose. Spin the axle so everything aligns, then tighten carriers and grub screws. A misaligned bearing wears quickly.

• Grub screws in good order: if a grub screw is damaged replace it with the Maranello M8x8 grub screw.

Grub Screw M8x8 for Axle Bearing 40/50 - Maranello

How to make the bearings last longer

Avoid pointing a pressure washer directly at the bearings: high-pressure water gets in and washes the grease away. After rain dry the kart thoroughly. Add the bearing check to your pre-race maintenance and find out everything about axles in the complete guide to axles.

Frequently asked questions

How can you tell if kart axle bearings need changing?

Lift the rear, remove the chain and spin the axle by hand. If you feel tight spots, noise, roughness or play, or the axle stops straight away instead of spinning freely, the bearings need replacing.

What's the difference between a 50x80 and a 50x90 axle bearing?

The first number is the inner diameter, that of the 50 mm axle. The second is the outer diameter, which must match the bearing carrier fitted on the chassis. Always check your kart's carrier before ordering.

What are the grub screws on the axle bearing for?

The grub screws lock the inner ring of the bearing onto the axle, so the axle can't slide sideways. They should be checked often and tightened properly, because vibration can loosen them.

By the TKS RaceLab technical team, with genuine Maranello Kart parts.

Questions about this topic?

Message us on WhatsApp: we answer personally, with the experience of people who live at the track. And if you want to drive a real racing kart, with Arrive & Drive you get into one of ours, ready on track. The right spare part? You will find it in the shop.

Arrive & Drive Pro by TKS RaceLab: 2026 karts with Rotax Senior MAX and DD2 engines, Alfano 7 telemetry and trackside technical support at Lonato, Franciacorta, Cremona and Ala. Message us on WhatsApp for information and availability.

TKS RaceLab | Performance Engineering Karting | tksracelab.com

📞 Contact

📞 +39 352 0280 133

Author: Sergio, TKS RaceLab | Published: 18 October 2026

TKS RaceLab is the Italian online store dedicated to karting: spare parts, accessories and everything you need to get on track. With Arrive & Drive you arrive at South Garda Karting (Lonato), Franciacorta, Cremona or Ala and find your kart ready to go. No hassle, just driving.

Comments


bottom of page